Specification Name: Smart Bicycle computer with light and electric horn Light Model: Strong/Low/SOS/Yellow Warning Light Light brightness: 250lm Battery: 1500mAh Light working hours: 5-8 hours Material: ABS Display: Speed /ODO/DST/ Riding time /Average speed Charging time: 2 hours Light Net Weight: About 108g Set Gross weight(with package): About 184g Waterproof: Water resistant Features : Ultrabright LED Bulb, Ultrabright & Creative USB Rechargeable Power Quick Charge Technology 4 Flashing Modes, much more safer in the dark 3 in 1 Functions, Built in Bike light, Bike Horn & Wired Bike Computer feature Easy Installation, Stable & Firm Bike Light with High Decibel Horn 1.Glare LED 2.Code display screen 3.Light switch 4.- SET button 5.+ Mode button 6.Speaker controller 7.Code table data sensor 8.Code table date receiver 9.Left and right yellow light 1.Ringer open button 2.Ringtone switch button Horn warning function, using double switch design, easy to operate ,first press the ring tones to open the button, press the ring toggle button can switch whistles in turn - horn sound - alarm sound- loud sound (A)(B) 2 seconds after the power is fully displayed, the display is as shown in A. The upper part is the current battery level indicator, and the lower part is the code table unit setting. The default is metric system. Press the MODE button oncce to switch to the inch system. Press MODE and SET key for 5 secondsat the same time, the system enters soft start, all settings are cleared, and the system repeats the above operation sa if it is newly powered on. The display is like the B chart. Press the MODE button again and the unit switchs to km/h again. (C) After setting, press the SET button to determine the speed unit. At this time, the display will be like C chart. Among them, 208 is blinking. 208 is the default tire circumference. Press MODE key at this time and the tire circumference will increase sequentially(209-210-220-- 315-10- 11-12--) The unit is CM. The setting range is 10CM~315CM. (D)(E)(F) After setting, press SET key to enter the initial total mileage setting, and the following D chart is displayed, in which the first 0 is blinking, press MODE key at this time, the first digit value increases sequentially, after setting the first digit, press the SET key, the second 0 flashes, press MODE key, the second value increases sequentially.This is turn sets thee fifth bit 0. Press the SET button again to exit the initial total mileage setting. The following E chart is displayed, where 1238.6 is the set initial mileage. If the initial mileage is not set, the F chart is displayed. At this point, all the initial settings of the code table are set and the system enters the standby state. If there is no key action after power on, the system will await for 10 seconds and automatically enter the default setting(tire circumference 208CM, initial total mileage is 0.0) The meaning of each symbol on the display screen Indicates the current riding speed. This interface represents a speed of 28.9 km/h Indicates the total mileage after the bike table is set Represents the single riding distance after the last system sleep and restart Indicates the maximum speed of riding after the system was last hibernated and restarted Represents the average speed of riding after the last system hibernation and restart Indicates the last time the system was hibernated before restarting Press SET button to switch to display ODO-DST-MXS-AVS-TM- When displayed, the display interface is displayed in the ODO-DST-MXS-AVS-TM scan, as shown below: After setting the tire circumference and the initial total mileage, enter the standby state, press the MODE key at this time, km h blinks, the system will automatically accelerate deceleration display. When the system is accelerating, the acceleration Upward symbol is displayed.When decelerating, the deceleration symbol Downwards isdisplayed. When the km h is not blinking, the system accelerates and decelerates without displaying the acceleration and deceleration symbols. After the system enters the standby state, there is no key or speed signal within 5 minutes. The system enters hibernation. When the system is in hibernation, the MODE or SET key is triggered and the system enters standby.
Tidak ada komentar:
Posting Komentar